DMP Electronics XR20 Troubleshooting Guide Page 32
- Page / 37
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
28
-CAN’T ACCESS LOCAL PROGRAMMING- (CONT’D)
* If panel is NOT communicating, contact DMP Technical Services and use ACCODE to get
into local programming or connect to panel with Remote Link and delete User Code 0.
After entering 6653 (PROG), does keypad display a message?
NO…
How many Keypads and/or expanders are there on the keypad bus?
• If there is more than one, some of the keypad or expander addresses are
probably set the same. Address the keypads and expanders, and then try
to get into programming.
• If still having problems, remove all keypads except #1 and try again.
Panel Won't Arm
When attempting to arm the system, the keypad immediately returns to the Time Display and
nothing arms. Here's what to check:
1) Are there areas in programming?
If no there are no areas programmed, the panel has nothing to arm.
* Enter Programming and check AREA INFORMATION programming.
* Areas must be assigned a name to become active.
2) Does the User Code have authority to Arm/Disarm the areas?
* Assign areas to code and/or check Profile (XR200/485 and XR500 series only) for
Arm/Disarm authority.
TECH NOTE: To assign areas to other User Codes in the system, YOUR CODE MUST HAVE
AUTHORITY FOR THE AREAS YOU ARE TRYING TO ASSIGN. If not, you must Initialize
codes and use the default code [99 + COMMAND] to assign the areas to the User Codes.
3) What Arming Mode is the panel in?
Most DMP panels offer three different MODES of arming. Each mode provides a slightly
different area configuration.These modes are:
ALL/PERIMETER Mode
–
Provides TWO, PRE-DEFINED AREAS of protection-
Area 1 = PERIMETER - Typically contains exterior door and window contacts and glass-break
detectors.
Area 2 = INTERIOR - Typically contains interior door contacts and motion detectors.
TECH NOTE: At arming the keypad displays [ PERIM ALL ].
Select PERIM to arm only the zones assigned to the Perimeter area.
Select ALL to arm all zones assigned to the Perimeter AND Interior areas.
NOTE: This mode is not available with XR200/485 or XR500 series panels.
-NOTES-
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
_____________
- Training Institute 1
- Troubleshooting Guide 1
- Introduction 5
- Built-in Tools 6
- XR200 & XR50 7
- -How it Works 8
- MAC address and Serial No 11
- Flash ROM chips 1 and 12
- Things to Know 13
- Resistor Values 15
- Output Information 16
- Voltage Outputs 3 – 10 16
- Annunciator Outputs 16
- Addressing Devices 17
- 770 series keypad 18
- Dipswitch locatio 18
- Clearing System Messages 19
- 4-Wire Bus Trouble 21
- Transmit Fail 21
- -WHAT TO DO 22
- Transmit Trouble 23
- System Trouble 23
- System Busy 24
- NON-POLLED ADDRESS 25
- Battery Trouble 26
- Tamper Trouble 27
- Wireless Trouble 28
- Printer Trouble 29
- Common Issues 31
- Panel Won't Arm 32
- ALL/PERIMETER Mode 32
- HOME/SLEEP/AWAY Mode 33
- AREA SYSTEM Mode 33
- Arming Procedure Chart 34
- Can’t Silence Bell/Siren 35
- Can’t Disarm 36
Related products and manuals for Security access control systems DMP Electronics XR20
(336 pages)Philips PD709/12 manuály
Uživatelské manuály a uživatelské příručky pro Videohry a konzole Philips PD709/12.
Poskytujeme 1 manuály pdf Philips PD709/12 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals