DMP Electronics XR10 User Manual Page 18
- Page / 26
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
14
XR10 Programming Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
8.9A MESSAGE TO TRANSMIT
You can send two report types to the receiver: Alarm and Trouble. These are represented by
the characters A and T. Press any top row SELECT key to display the zone's report options.
ALARM - Selecting A, allows an alarm report to be sent to the receiver and the bell output to
activate according to zone type. See section 7.4, Bell Action. The zone name appears in the
panel's alarmed zones status lists.
TROUBLE - Selecting T allows a trouble report to be sent to the receiver and the zone name
to appear in the panel's alarmed zones status lists.
LOCAL - When you select L, an alarm report is NOT sent to the receiver. The bell output still
activates according to zone type and the zone name appears in the panel's alarmed zones
status lists. NOTE: If Pager is YES in Communication, the alarm report is also sent to the
designated pager.
– (dash) - When you select a dash, reports are NOT sent to the receiver. The bell output
does not activate and there is no display in the panel's alarmed zones status list. Only the
Output Number selected in section 8.9B activates.
8.9B OUTPUT NUMBER
You can specify any of the outputs on the XR10 to be activated by a zone condition. The
output can be activated regardless of the report to transmit or whether or not the zone is
programmed as local. An output activated by a non-24 hour armed zone is turned off when
the zone's area is disarmed by a user.
To enter an Output Number, press a top row SELECT key followed by the output number 1 to
4. Press the COMMAND key.
8.9C OUTPUT ACTION -
Entering an Output Number in section 8.9B displays this prompt that allows you to assign an
output action to the relay.
A description of the available output actions is given below:
STEADY - The output is turned on and remains on until the area is disarmed, an output cutoff
time expires, or the output is reset from the keypad User Menu.
PULSE - The output alternates one second on and one second off until the area is disarmed,
an output cutoff time expires, or the output is reset from the keypad User Menu.
MOMENTARY - The output is turned on only once for one second.
FOLLOW - The output is turned on and remains on while the zone is in an off normal, or bad
condition. When the zone restores, the output is turned off.
After you've made the three selections in sections 8.9A through 8.9C, the display prompts
you for the same three selections for Disarmed Short, Armed Open, and Armed Short
conditions. If the zone is a 24 hour type, only the Armed Open and Armed Short conditions
are displayed. When you've programmed all of the zone conditions, the Swinger Bypass
selection is then displayed.
8.10 SWINGER BYPASS
YES allows the zone to be bypassed by the panel after three alarm, trouble, or local trips
within one hour. Selecting NO disables swinger bypassing for this zone.
After the first trip, if the zone does not trip 2 more times before the remaining time expires,
the bypass trip counter returns to zero and the zone must trip a full 3 times within the next
hour to be automatically bypassed.
A swinger bypass is sent to the receiver if Bypass Reports is YES. See section 5.5.
Bypassed zones are automatically reset when the area they’re assigned to is disarmed. All
24 hour zones are reset when the system is disarmed.
8 - ZONE INFORMATION
MSG: TROUBLE
A T L -
OUTPUT NO: 0
ACTION:
STD PLS MOM FOLW
SWGR BYP YES
- XR10 Command Processor Panel 1
- Programming Guide 1
- MODEL XR10 PROGRAMMING GUIDE 2
- TABLE OF CONTENTS 3
- Introduction 5
- 1.4 Programmer Lockout Codes 6
- 1.5 Reset Timeout 6
- 1.6 Special Keys 6
- S Y S T E M O N 7
- How it works: 11
- 8 - ZONE INFORMATION 19
- PRIORITY NO 19
- ENTRY DELAY: 1 19
- CRS ZONE NO 19
- ZONE NO: – 19
- 11.1 Status List 21
- 11.3 4-2 reporting operation 21
- 11.4 Zone Type Specifications 22
- 11.5 Zone Type Descriptions 23
- 11 - APPENDIX 24
- 11.9 How to Read this Table 25
- Digital Monitoring Products 26
Related products and manuals for Security access control systems DMP Electronics XR10
(28 pages)Philips PD709/12 manuály
Uživatelské manuály a uživatelské příručky pro Videohry a konzole Philips PD709/12.
Poskytujeme 1 manuály pdf Philips PD709/12 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals